problema memorie SD

9 posts / 0 new

2. March 2011 - 13:28

pigulici

problema memorie SD

Am primit un ap foto Pentax optio E20 cu un card noname SD de 1gb, l-am conectat prin cablu de date usb si in mandriva 2010.2 64b kde 4.5 si la win 7 64b, tot a mers cum trebuie, il vedea, copiam,etc...m-a mancat sa ii dau format la sd din apartul foto, de atunci nu il mai pot accesa, cand dau lsusb imi da:
"Bus 003 Device 003: ID 0a17:007e Pentax Corp."
, in fstab nu il vede, in mcc la local disk nu il vede, dar in mcc la hardware, la Usb mass storage devices il vede ca Pentax optio E20, tot aici la Hard Disk il vede ca sdb :
"Identification
Vendor: ‎
Description: ‎ (PENTAX
Disk identifier: ‎
Media class: ‎hd (Mass Storage|SCSI|Bulk (Zip))
Bus identification
Vendor ID: ‎0x0a17
Target id number: ‎0x007e
Connection
Bus: ‎SCSI (USB) (3)
Channel: ‎0
Logical unit number: ‎0
Target id number: ‎0x007e
Device
Old device file: ‎/dev/sdc
Misc
Device USB ID: ‎3
Geometry: ‎// (CHS)
Disk controller: ‎10
Module: ‎usb_storage (usb_storage)"

daca dau de aici Run config tool, ma duce la partitionig, dar aici numai apare.
Am incercat si pe alt pc si la fel se manifesta, poze sa fac si sa salvez pe el, din aparatul foto, se poate, dar nu il vad in pc prin cablul de date, vreo idee cum sa il formatez din pc, sau sa il accesez(fara a mai cumpara un card reader)?

2. March 2011 - 23:02

cgherman

scoate cardul si du-l la un

scoate cardul si du-l la un amic cu un laptop cu reader. daca il vede atunci e o setare a aparatului

vezi in meniu cum sa vada cardul. sa fie ca memorie usb - ori similar

Cristian
http://www.mandrivausers.ro

3. March 2011 - 10:32

pigulici

deh, greu de gasit unu cu

deh, greu de gasit unu cu card reader prin zona, mai sap, am testat si cu alt card sd sinu apare problema...ma gandeam poate am noroc de vreo comanda sa ii dau un format fortat...

3. March 2011 - 11:07

symbianflo

pai incearca testdisk

pai incearca testdisk+photorec , oricum un card reader costa 2-3 euri...daca ai apartul poate e o cheltuiala care merita...
Daca zici ca diskdrake il vede, poti sa il si formatezi , ar trebui sa-l montezi manual , si cauta in mtab dupa ce l-ai infipt in usb,
ar trebui sa-l monteze in /media, daca nu formateaza cu minutza :D
PS:
asa dupa miros as zice ca is doar probleme de permisuri.

http://www.mandrivausers.ro/ MRB aint no shit , :p Linux user number 507107 Nu dați banii pe prostii, puneți Linux pe PISI ![ARLUG]

Unix is user-friendly. It’s just very selective about who its friends are

4. March 2011 - 10:24

pigulici

nu imi apare in mtab

4. March 2011 - 10:57

pigulici

mai sap, nu ma las pana nu il

mai sap, nu ma las pana nu il dau pe spate
am dat modprobe usb-storage si dmesg si iata rtezultatul:
usb 3-1.1: new full speed USB device using ehci_hcd and address 3
usb 3-1.1: New USB device found, idVendor=0a17, idProduct=007e
usb 3-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 3-1.1: Product: PENTAX Optio E20
usb 3-1.1: Manufacturer: PENTAX
Initializing USB Mass Storage driver...
scsi10 : usb-storage 3-1.1:1.0
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
scsi 10:0:0:0: Direct-Access 1.00 PQ: 0 ANSI: 2
sd 10:0:0:0: Attached scsi generic sg2 type 0
sd 10:0:0:0: [sdb] 1990656 512-byte logical blocks: (1.01 GB/972 MiB)
sd 10:0:0:0: [sdb] Write Protect is off
sd 10:0:0:0: [sdb] Mode Sense: 1f 00 00 08
sd 10:0:0:0: [sdb] Assuming drive cache: write through
sd 10:0:0:0: [sdb] Assuming drive cache: write through
sdb: sdb1
sd 10:0:0:0: [sdb] Assuming drive cache: write through
sd 10:0:0:0: [sdb] Attached SCSI removable disk
usb 3-1.1: reset full speed USB device using ehci_hcd and address 3
usb 3-1.1: reset full speed USB device using ehci_hcd and address 3
usb 3-1.1: reset full speed USB device using ehci_hcd and address 3
usb 3-1.1: reset full speed USB device using ehci_hcd and address 3
sd 10:0:0:0: Device offlined - not ready after error recovery
sd 10:0:0:0: [sdb] Unhandled error code
sd 10:0:0:0: [sdb] Result: hostbyte=DID_ABORT driverbyte=DRIVER_OK
sd 10:0:0:0: [sdb] CDB: Read(10): 28 00 00 1e 5f f0 00 00 08 00
end_request: I/O error, dev sdb, sector 1990640
Buffer I/O error on device sdb, logical block 248830
sd 10:0:0:0: rejecting I/O to offline device
ceva idei?

4. March 2011 - 11:15

pigulici

si la comanda /proc/bus/usb

si la comanda /proc/bus/usb/devices apare:
T: Bus=03 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#= 3 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=0a17 ProdID=007e Rev= 0.01
S: Manufacturer=PENTAX
S: Product=PENTAX Optio E20
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 96mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms

4. March 2011 - 11:59

symbianflo

pai si de ce nu ii dai in

pai si de ce nu ii dai in gura cu mount /bla bla /sdb ??? daca tot il recunoaste monteaza-l tu . sau daca il vede diskdrake in mcc monteaza-l de acolo daca crezi ca din shell nu poti.